- Home
- Help Center
Collection: Help Center
Help Center
Click here to watch the video.
More TS2 tutorial videos, please click here.
Click here to watch the video.
More TS2 tutorial videos, please click here.
Click here to watch the video.
More TS2 tutorial videos, please click here.
Click here to watch the video.
More TS2 tutorial videos, please click here.
Please click here to watch the tutorial video.
More TS3 tutorial videos, please click here.
Please click here to watch the tutorial video.
More TS3 tutorial videos, please click here.
Click here to watch the video.
More TT Series tutorial videos, please click here.
Click here to watch the video.
More TT Series tutorial videos, please click here.
Click here to watch the video.
More TT Series tutorial videos, please click here.
Please click here to watch the tutorial video.
More TTC450 tutorial videos, please click here.
Please click here to watch the tutorial video.
More TTC450 tutorial videos, please click here.
Please click here to watch the tutorial video.
More SP-5 tutorial videos, please click here.
More tutorial videos for Two Trees 3D printers, please click here.
Please click here to watch the tutorial.
Please click here to watch the tutorial.
Please click here to watch the tutorial.
1. Make sure the machine is turned on. (The fan of the laser module is spinning)
2. Make sure the USB cable is connected to the interface on the machine.
3. Check whether the computer can recognize the COM signal of the machine. (or into another port on your computer)
4. In the previous step, if there is no new com, you need to install a CH340 driver. It can be obtained from the TF card file. Or install the CH340 driver through the lasergrbl tool.
5. Set the correct baud rate, 115200
6. Select the correct "com" port in the software. (you can try every com port)
7. Click Connect.
8. If the above steps still fail to connect, please restart your computer, and then perform steps 5-7 again. (because there may be a software conflict).
9. If it still fails, and there is a prompt message in the dialog box on the left in the software, you need to update the firmware, Then do the above steps again.
https://drive.google.com/file/d/19Ze3zGDUTj8xklurz5gZStk2L16fjRfn/view?usp=share_link
The working size is 450mmx450mmx60mm.Expander kits and height riser accessories can be purchased to expand the size.
Wood, Plastic, Paper, Leather, Bamboo, Sponge Paper, Alumina, Stainless Steel, PVC expansion sheet, Acrylic etc.
Install the software lightburn, you can use it on the mac and Windows system, only 30 days free, after 30 days you need to pay for it. LaserGRBL does not support MAC systems.
1. Remove the screws from the timing wheel; 2. Slide the components on both sides of the Y-axis to the same scale; 3. Secure the screws.
1. Download and install the CH340 driver onto your computer.
2. Turn on the machine.
3. Connect the computer and the machine with a data cable (a MAC adapter is required).
4. Launch GRBL software, select the appropriate serial port and baud rate, and then click Connect (if using Light Burn
software, select the appropriate interface).
5. Click the Move button to check whether the machine moves normally
1. Remove the screws from the motherboard housing and disassemble the housing;
2. Connect the cable to the screen (pay attention to screen interfaces 1 and 2).
3. Thread the cable through the motherboard housing’s reserved hole;
4. Plug the wiring port into the corresponding port on the motherboard (the cable for interface 1 is plugged into the
left connector on the motherboard, and the cable for interface 2 is plugged into the right connector);
5. Turn on the computer and test the screen.
1. The probe cannot be moved due to mechanical failure (move the probe up and down manually).
2. The limit switch cannot rebound if it has been damaged or moved. （ Disassemble the laser head housing for
inspection ）
3. Incorrect wire terminal interface connection (reinstall and double-check).
4. Wire damage and wrong wire sequence (check and repair).
1. no power (check and restart);
2. a faulty switch (replace);
3. Inadequate power cable interface contact (check and firmly insert it);
4. Short circuit on the main board (check and repair it one by one)
1.Check whether the X and Y axis limit switches are damaged if there is abnormal noise when returning to zero;
2. The firmware parameters are incorrect, which results in the wrong direction. In this case, please flash the firmware.
1. Abnormal zero return (inspect and repair the limit switch);
2. Impact frame for movement (screw, motion range setting error);
3. In case of transmission range of motion becomes stuck due to sundries or pulling (inspect and remove);
1. Determine whether to engrave or cut;
2. To adjust the focus, use the fixed focus column and the tutorial reference instructions.
3. Run tests on the test board and make any necessary adjustments
Gcode files can be generated on the computer by LightBurn or GRBL software:
1.Open the software and drag in the file to be engraved;
2.Set the appropriate parameters;
3.Save it as a Gcode file.
1.Wiring error (check whether other functions do not work as well);
2. Error in line sequence (tools can test positive and negative voltage);
3. The laser head is damaged. (need to replace the laser head).
1. Open the TF Card files to find the installation package or download it from the APP Store.
2. Connect your smartphone to WiFi.
3. Open the APP to enter the IP address on the machine screen and click Connect;
4. Go to the operation interface and start using the APP
1. Turn off and reconnect the machine;
2. Insufficient contact of the USB cable socket (replace the interface);
3. Inadequate adapter contact (MAC computer).
4. Turn off the power saving mode of the computer’s USB port;
1. Adjust the right tensioner（tighten clockwise, loosen counterclockwise）and push it to the tightest, tighten the screw
until the gap with the sheet metal is eliminated, and then tighten it for an additional half turn; Test: the laser module can
slide freely after the machine is tilted 45 degrees.
Y axis:
1. Locate the adjusting screw at the bottom of the Y axis (tighten clockwise, loosen counterclockwise)
2. Tighten it to the maximum with a wrench, then tighten the screws until the gap with the sheet metal is eliminated, then
tighten them for an additional turn; Test: The X axis can slide freely after the machine is tilted 45 degrees.
1. Remove the flame sensor’s shell;
2. Turn the white screw with a wrench (increase sensitivity clockwise and decrease it anticlockwise);
3. After the sensitivity reaches the minimum, turn it half a turn in the opposite direction to ensure that the flame sensor will
be triggered. (When the function needs to be turned off, it can be adjusted to the lowest level to play the role of being
turned off.)
1. Obtain an air pump;
2. Connect to the air pump’s air outlet port via the air pump hose attached to the air pump;
3.Connect one end of the air pipe to the air pump;
4. Install the air pipe connector attached to the machine onto the reserved interface on the laser module.
5. Insert the other end of the air pipe into the air pipe connector.
6. After powering up the air pump, adjust the air volume by adjusting the knob on the air pump.
1. Check whether the motor’s wiring is well connected (re-plug the wiring);
2. Check whether the motor wire sequence is correct (if the motor shakes but does not rotate normally, it is the wrong wire
sequence);
3. Inspect the motor for damage.
4. Check whether the corresponding drive is damaged.
1. Turn off the electricity;
2. Take the laser module out of the machine;
3. Wipe the external lens with an alcohol-soaked cotton swab.
4. Let it dry naturally;
5. Install the laser module back. (never disassemble without power off or use without drying)
1. Immediately turn off the machine;
2. Inspect the engraving condition (if there is any potential safety hazard (fire), please remove it as soon as possible);
3. Restart the engraving and keep an eye on it.
1. Use tools to loosen the screws on the machine’s synchronous wheel;
2. Move the synchronizing wheel to a proper position;
3. Retighten the screws on the timing wheel
1.Install the CH340 driver on the computer;
2.Power on the machine;
3.Use the data cable to connect the computer and the machine (MAC should pay attention to whether the adapter port is suitable);
4.Open the GRBL software to select the correct serial port and baud rate, and then click connect (if using lightburn software, please select the correct interface);
5. Click the move button to see if the machine moves properly.
2.1 Screen interface introduction; 2.1.1. Laser out of the light of the interface (manual control of the laser on).
2.1.2. Control interface (move, set home, return home, unlock, return to zero, etc.);
2.1.3. Engraving page (read TF card file).;
2.1.4. Setup page (firmware version information, switching Y-axis and rotary table, WiFi information).
2.2 Execute the engraving process using the screen;
2.2.1 Computer editing file (.nc or .Gcode file) needs to be saved to the TF card first;
2.2.2 Inserting the TF card into the machine;
2.2.3 Select the file to be engraved and enter the engraving setting interface;
2.2.4 Move to the desired location and click on Set Origin;
2.2.5 Click on the edge patrol, if the position is not suitable, repeat the previous operation;
2.2.6 If the position is correct, click “√” in the pop-up window to start engraving.
Due to the resistive screen (which requires a certain amount of pressure to trigger, you can use your fingernail or pen);
2.The screen film is not torn clean, thus squeezing the screen, please remove the residue after inspection.
1. Not energized (check and energize);
2. Switch damaged (needs to be replaced);
3. Poor contact with the power cord interface (view and plug the interface tightly) ;
4. Motherboard short circuit (check and repair).
1. If there is a strange noise when returning to zero, check whether the X and Y axis limit switches are cocked, if they are cocked, please press them flat to make the limit switches work;
2. Incorrect firmware parameters, resulting in the wrong direction (please re-flash the firmware).;
3. The gear switch on the back of the machine is not set to “1” (please set it to “1”).
1. Abnormal noise when returning to zero (check whether the limit switch works and repair it);
2. The frame hits the frame during the movement (screws, the movement range is set incorrectly);
3. There is debris or pulling in the transmission range, which causes the jam (please check and remove the debris).
1.determine whether it is to be engraved or cut;
2.Adjust the focus using a fixed focus column and a tutorial with reference to the instructions;
3. testing on a test board and then fine-tuning according to the results.
1.Open the software and connect the machine;
2.Drag in the picture to be engraved;
3.Set parameters (speed, power, etc.) according to prompts;
4.Determine the engraving range by “set user origin” and “edge patrol”;
5. Start Engraving.
1.Open the software and connect the machine.
2.
Drag in the picture to be engraved.
3.Find and enter the layer to set parameters (power, speed, etc.).
4.Determine the engraving range by “set user origin” and “edge patrol”.
5. Start engraving.
Gcode files can be generated by lightburn or GRBL software on your computer.
1. Open the software and drag in the files to be engraved;
2. Set the appropriate parameters;
3. Save the file as a Gcode file.
1.Wiring errors (you can check if other functions are also not working);
2.Wrong wiring sequence (you can test the voltage positive and negative through the tool) ;
3. Laser head damage (need to replace the laser head).
14.1. Preparation for APP use;
1.
Install the app on your phone (download it from the application mall or open the TF card to find the installation package for installation);
2.Open the machine settings page;
3.Use your phone to connect to the machine WiFi;
4.Open the APP enter the IP address on the machine screen and click connect;
5.Enter the operation interface and start using APP;
6. Insert the TF card to use as storage data.
14.2. Use the APP to execute the engraving process ;
14.2.1 Select the pattern you want to engrave in the creation module or in the file list (you can upload album pictures) ;
14.2.2 Click next for pattern setting ;
14.2.3 Click next for parameter setting (size, power, speed) ;
14.2.4 Click Move for position selection.;
14.2.5 check whether the position is correct by the edge patrol function (repeat the previous step if it is not correct);
14.2.6 Click Engrave to upload the file to start engraving..
15.1. Preparation for Web use;
1.
open the machine settings page to find WiFi and IP address information.
2.Connect the computer to the machine’s WiFi;
3.Open the computer browser and enter the IP address on the machine;
Enter the control interface and start using it.
15.1. Use the APP to execute the carving process;
15.1.1 Enter $H in the input box of the control interface to make the machine return to zero;
15.1.2 Select a file or upload a local file in the “SD File” interface;
15.1.3 Enter the control interface to set parameters (power, speed);
15.1.4 Move the position and determine the home position;
15.1.5 Check if the position is correct by using the (if not, repeat the previous step);
15.1.6 Click the engraving button to start engraving.
1.Check whether the belt of each axis has tension, and re-adjust the tension of the timing belt;
2.
Whether the machine hardware (screws, etc.) is tightened;
3.Check the condition of the machine transmission parts have no jamming or loose collapse shaking;
4.Adjust the eccentric nut around the transmission position;
5. Fxed laser parts screws are not locked, not locked will lead to shaking (laser head focus knob loose lead to focus change).
1.Turn off the machine to reconnect;
2.Poor contact with the USB cable jack (replace the interface);
3.
Bad contact with the adapter (MAC computer);
4. Close the computer USB port power saving mode.
1.Loosen the belt pressure plate screw;
2.Tighten the timing belt;
3.Tighten the screws;
4. Synchronous belt a little point of preload, but not very tight.
1.Use a wrench tool to adjust the eccentric nut on the inside of the pulley, adjust to slight friction with the hand to paddle the pulley is appropriate;
2. If the carving effect is not good, you can try to re-adjust once again.
1.Open the machine setup page.
2.Select the option to use the rotary module.
3.follow the on-screen instructions.
1.Install the MKSLaser Tool tool ;
2.open the tool and select the first item to enter ;
3.select the correct serial port and baud rate ;
4.first click the Erase button to erase the original firmware ;
5.select the firmware and click Start, and wait for the refresh to complete ;
6. Reboot the machine (please use the manufacturer’s firmware).
1.open the acrylic cover door;
2. Find the switch on the right side and turn it to off (red button).
Usually there are two situations:
1.
After the data cable is connected, if the computer fails to recognize the serial port of the engraving machine, it means that the CH340 driver file has not been installed;
2.Install the CH340 driver file, if the string still cannot be displayed, try to replace the USB data cable or the computer interface;
Use manual or computer control to move the Y-axis separately, and observe whether the movement is stuck; check whether the motor rotation is stuck; whether the motor cable is tightly inserted; try to replace the engraving software;
Check all belts and adjust tension;
Whether the transmission parts are stuck or loose, adjust the eccentric nut around the transmission position;
The screws that fix the laser components are locked tightly, otherwise it will cause shaking.
Check all belts and adjust tension;
Whether the transmission parts are stuck or loose, adjust the eccentric nut around the transmission position;
The screws that fix the laser components are locked tightly, otherwise it will cause shaking.
Check whether it is connected to the machine;
Check if there is an error code on the console after connecting to the software, if so, you need to re-flash the firmware;
Try disconnecting and reconnecting;
Check whether the TF card is inserted into the machine;
Check whether the file naming is complicated or too long;
Install the software lightburn, you can use it on the mac and Windows system, only 30 days free, after 30 days you need to pay for it. LaserGRBL does not support MAC systems.
Wood, Plastic, Paper, Leather, Bamboo, Sponge Paper, Alumina, Stainless Steel, PVC expansion sheet, Acrylic etc.
LightBurn is a paid software, only 30 days for free.LaserGRBL , it's free.
The working size is 300mmx300mmx60mm.Expander kits and height riser accessories can be purchased to expand the size.
1. Make sure that the machine has successfully connected to the laserGRBL software of the computer. Because when the connection is not successful, the laser module cannot emit laser light.
2. Check whether the motor cable is installed correctly. (you can try to reinstall)After being connected correctly, the fan on the laser module will rotate.
3. If the fan does not rotate, open the main control box and find the laser interface, and check whether the cable is disconnected, "+12v-" and "+TTL-" (you can try to reinstall the cable).Inserting the wrong port will also cause no light, so you need to check: Are these 2 ports installed correctly?Correct: "+TTL-" cables have 1 wire, and "+12v-" cables have 2 wires.
4. If the fan is rotating.Please check: whether the cable of the "+TTL-" interface can conduct current, and only when the current is conducted can the laser be emitted.Please let us know if this cable is damaged.
5. If the cable is normal and the fan is normal, perform the following steps:Let the machine start engraving and check if there is a new flashing light on the control PCB board.If so, it means that the main control board is sending signals to the laser module, and the cable is fine. Possible result: the laser module is faulty.If there is no flashing light, it means that the software on the computer has not turned on the M3\M4 mode or the power value is set to 0.How to solve: Modify the power value or reinstall the LaserGRBL software.
6. If none of the above steps solve the problem, re-refresh the machine firmware.
https://drive.google.com/drive/folders/1__JtIIZHfi8TAPhXsiiXKBlhTR9FHXv9?usp=share_link
https://drive.google.com/file/d/1c4WYN0WqScFXjEsPsaMq3QSpiwnv4PRr/view?usp=share_link
1. Check: In the laserGRBL software, when loading the pattern, is the setting value of S sufficient?Please set the maximum S value to 1000, and then perform the engraving test again.
2. In the laserGRBL software, enter $30=1000 in "type gcode here", and click the "Enter" key on the keyboard. Then do the engraving test again. (This is to set the default maximum power value of the laser to 1000)
3. Turn off the power of the machine and check whether the bottom lens of the laser module is dirty. Please use a cotton swab to wipe the laser lens to make sure the lens is clean, and then perform the engraving test again.
4. Properly reduce the speed. The speed of the plank is about 3000mm/min. Note that it is not mm/s. (lower speed possible)
5. Refer to the instruction manual to readjust the distance between the laser head and the object to be engraved. If the focus is not accurate, it will also result in failure to engrave. You can try different distances to see if there is a change.
6. If none of the above steps can solve the problem. Please project the laser on a farther wall in a place where there are no other people, take a picture and send it to us. (wear glasses and be careful)
https://drive.google.com/drive/folders/1YhnOJrokoGIlzK8Gt-KowzRl33gYFYNY?usp=share_link
1. First test whether the motors on both sides can work normally. Unplug the motor cable on one side, use the software to control the Y-axis movement, and test the movement twice to know.
2. If it is not the problem of the motor, first loosen the screws on both sides of the X-rail.3. Check: Whether the wheels of the left and right tackles are attached to this aluminum rail, stable and without obvious shaking.If not, use a wrench to twist the hex posts so the wheels fit.
3. Align the left and right pulleys on the aluminum rail with the same scale, and re-lock the screws.
4. Adjust the tightness of the timing belts on both sides to make them similar.
https://drive.google.com/drive/folders/1I_AWUqLNV5iGxhhEowk_6fUimGdzBZnb?usp=share_link
https://drive.google.com/drive/folders/1jBy0_q95VV31Grc12bhXxZDMCIPdWz5x?usp=share_link
It may be caused by the following two conditions.
A. Exceeding the working stroke of the machine.
B. Friction of transmission parts.
1. The working stroke of the machine is exceeded.Please try to perform the following operation.Set the software parameters according to the nominal working size of the machine, TTS working range is 300mmx300mm.
2. Friction of transmission parts.Please try to perform the following operations.2.1-Turn off the power of the machine, move the X-axis left and right, and move the Y-axis back and forth to check if there is any sticking or difficult movement.2.2-Test each drive part individually.Adjust the screws or add lubricant according to each different part.
1. Adjust the hexagonal column of the pulley with a spanner so that the wheel fits the rail and is smooth and does not wobble. And move the X-axis and Y-axis without jamming.
2. X-axis and Y-axis timing belt should be adjusted to pre-tightened state.
3. The screws fixing the laser module should be ensured to be firm and not shaking.
4. Check: whether the motors on both the left and right sides of the Y-axis are working normally, you can unplug the motor cable on one side first to verify.
5. Lower the running speed appropriately.
6. Check: whether the wheels are worn or there are foreign objects in the rails.
https://drive.google.com/drive/folders/1I_AWUqLNV5iGxhhEowk_6fUimGdzBZnb?usp=share_link
https://drive.google.com/drive/folders/1jBy0_q95VV31Grc12bhXxZDMCIPdWz5x?usp=share_link
1. Change the usb port of the computer to use. Loose connector or insufficient voltage may cause the connection to be interrupted.
2. The USB cable is placed in a place to avoid touching. Pulling the USB cable may also cause the connection to be interrupted.
3. LasergGRBL in the settings, "Threading Mode" value to choose a lower speed mode.
4. The above steps do not solve the problem, refresh the machine firmware.
https://drive.google.com/drive/folders/1QbCVB9g4dxsDvE2qF_30mB41PONG7nYE?usp=share_link
https://drive.google.com/drive/folders/1Y2EOxcaPHsIL0rYlnMaOmRC-OAQOHpvl?usp=share_link
1. Move the X-axis and Y-axis, and observe whether the moving direction is correct?If the moving direction is not correctIn the "type gcode here" of LaserGRBL software, type $RST and hit "Enter" on the keyboard. Then perform the move test and engrave test. (This is to restore the default value)
2. If the problem is not solved, please update the firmware.
https://drive.google.com/drive/folders/1K9N3bqym9KiP4W0WiND4kPBqUZ9mtuYN?usp=share_link
https://drive.google.com/drive/folders/1Y2EOxcaPHsIL0rYlnMaOmRC-OAQOHpvl?usp=share_link
1. In the "type gcode here" of the LaserGRBL software, input $32=1, and click the "Enter" key on the keyboard. (Enable Engraving Mode)
2. Select M4 mode in laserGRBL.Turn off "Constant Power Mode" in Lightburn.M4 is the engraving mode, which is more suitable for engraving.
3. If the problem is not solved, please update the firmware.
https://drive.google.com/drive/folders/1SCu5LlaNN7ZvDuZkpjAN2WNfcP-QCKbj?usp=share_link
https://drive.google.com/drive/folders/1Y2EOxcaPHsIL0rYlnMaOmRC-OAQOHpvl?usp=share_link
Install the software candle, which can be used for free on the Windows system, it does not support the MAC system.
The working size is 460mmx460mmx60mm.Expander kits and height riser accessories can be purchased to expand the size.
1. Make sure that the machine has been successfully connected to the candle software of the computer. Because when the connection is not successful, it is impossible to control the operation of the motor.
2. Check whether the motor cable is installed correctly. (you can try to reinstall)
3. If there is a motor that can work normally, you can open the control box to find the main control board, and exchange the motor cables in the control box.After swapping, if it doesn't work normally, it means there is a problem with the cable, please let us know and replace it with a new one.
4. If the motor vibrates but does not move, then there may be a problem with the line sequence of the cable. You can use an object with a sharp corner as a tool to exchange the sequence of the two lines in the middle.
5. After exchanging the order of the cables, if the direction is wrong, you can exchange the order of the two similar lines on the left.
6. After checking the third step, if the original normal motor does not work, then the driver of the main control board may be damaged. Please let us know and get a new one.When telling us, it would be better if there is a video, so that we can better confirm the problem and replace it with new accessories.
It may be caused by the following two conditions.
1. Exceeding the working stroke of the machine.
2. Friction of transmission parts.
1. The working stroke of the machine is exceeded.Please try to perform the following operation.Set the software parameters according to the nominal working size of the machine, TTC450 working range is 460mmx460mm.
2. Friction of transmission parts.Please try to perform the following operations.
2.1-Turn off the power of the machine, move the X-axis left and right, and move the Y-axis back and forth to check if there is any sticking or difficult movement.
2.2-Test each drive part individually.Adjust the screws or add lubricant according to each different part.
1. Make sure the adapter or power cord is connected to the voltage and the indicator light is on.
2. Press the switch repeatedly to observe the changes of the machine.
3. Remove the TF memory card and reboot.
4. Unplug all motor cables. Make it disconnect, then reboot.If the machine can be turned on, then plug the cables back in order.When the machine shuts down again, the cable may be damaged.
5. Open the control board box and check: whether the switch wire is falling off.
6. Use other adapters of the same specification.
1. Successfully connect the software and the machine,
2. Enter $$ in the control bar to call up the parameter page.
3. Find the three values of $100, $101, and $102, and check whether they are all 80,
4. If there is a value other than 80, please modify it to 80.
1. Successfully connect the software and the machine,
2. Enter $$ in the control bar to call up the parameter page.
3. Find the value of $3, and modify it according to $3=0, $3=1, $3=2, $3=3, $3=4, $3=5,
4. After each modification, check whether the moving direction of each axis to the west is correct. We can modify the direction correctly at most 6 times.
1. Read the manual in detail and follow the steps to install. Click Here.
2. Watch the installation video and follow the steps to install. Click Here.
1. You can search for the attached link to understand the basic usage of the software. Click Here
2. Learn more functions through website
Generate Gcode program file in EASEL
1. Open the URL: https://www.inventables.com/technologies/easel
2. Log in through your personal account and password (if you don’t have one, you can register temporarily)
3. Familiarize yourself with the settings according to the video
4. Create a new model
5. Set the parameters of the model (size, cutting depth, etc.)
6. Export the file and save it
1. To upgrade the firmware, you need to use the "MKSLaserTool" software.
2. When using the "MKSLaserTool" software, please do not delete the firmware by mistake. After the firmware is deleted, garbled characters and errors will appear. As a result, the engraving machine cannot be used.
Please refer to the video to use the workpiece fixture correctly, please pay attention to clamp the workpiece to prevent the workpiece from loosening during the engraving process
https://drive.google.com/file/d/1draUMEnlYu9ZXtMFpglnheKUBddMj-fB/view?usp=share_link
Please refer to the video to set the knife correctly.
https://drive.google.com/file/d/1adGrbsUqau7poyXgQW2yejwTJDPUpkk0/view?usp=share_link
1. Remove the cable tie on the cable (be careful not to hurt the cable)
2. First move the left shaft to the top, then unplug the Y2 motor wiring
3. Move the right axis to the top4. Finally, plug back the Y2 motor wiring
https://drive.google.com/file/d/14AcEcT2QD3k9TnYDq1VOhyIHYLIfpLEc/view?usp=share_link
• Please refer to the video to install the spindle kit correctly
https://drive.google.com/file/d/1YkZGkIT8DESjimA3nMW9D76dQfAXrOFZ/view?usp=share_link
1. Purchase a circular laser module kit
2. Disassemble the motherboard control box and find the motherboard
3. Insert the laser head cable into the TTL interface on the motherboard
4. Reinstall the motherboard control box
5. Install the circular laser module on the spindle and connect the wiring
6. Start and connect the machine
7. Brush the laser firmware into the machine and restart the machine, import the configuration file
8. Use the software to connect to the machine and make modifications to individual settings
9. Engraving test
https://drive.google.com/file/d/1rVZowWFQeTCYRUlQevKrNK5eXJWkRs2W/view?usp=share_link
1. Remove the spindle motor fixture
2. Install the 20W laser kit on the Z axis
3. Disassemble the motherboard control box and find the motherboard
4. Insert the laser cable into the TTL interface on the motherboard
5. Reinstall the motherboard control box
6. Connect the wires to the laser module
7. Brush into the laser firmware for the machine
8. Restart and connect the machine, import the configuration file
9. Modify some settings
10. Engraving test
https://drive.google.com/file/d/1mdR6GZiw6KCSHvZ5m0jJwXownPAqpN6g/view?usp=share_link
1. Make sure that the machine has successfully connected to the laserGRBL software of the computer. Because when the connection is not successful, the laser module cannot emit laser light.
2. Check whether the motor cable is installed correctly. (you can try to reinstall)After being connected correctly, the fan on the laser module will rotate.
3. If the fan does not rotate, open the main control box and find the laser interface, and check whether the cable is disconnected, "+12v-" and "+TTL-" (you can try to reinstall the cable).Inserting the wrong port will also cause no light, so you need to check: Are these 2 ports installed correctly?Correct: "+TTL-" cables have 1 wire, and "+12v-" cables have 2 wires.
4. If the fan is rotating.Please check: whether the cable of the "+TTL-" interface can conduct current, and only when the current is conducted can the laser be emitted.Please let us know if this cable is damaged.
5. If the cable is normal and the fan is normal, perform the following steps:Let the machine start engraving and check if there is a new flashing light on the control PCB board.If so, it means that the main control board is sending signals to the laser module, and the cable is fine. Possible result: the laser module is faulty.If there is no flashing light, it means that the software on the computer has not turned on the M3\M4 mode or the power value is set to 0.How to solve: Modify the power value or reinstall the LaserGRBL software.
6. If none of the above steps solve the problem, re-refresh the machine firmware.
https://drive.google.com/drive/folders/1__JtIIZHfi8TAPhXsiiXKBlhTR9FHXv9?usp=share_link
https://drive.google.com/file/d/1c4WYN0WqScFXjEsPsaMq3QSpiwnv4PRr/view?usp=share_link
1. Check: In the laserGRBL software, when loading the pattern, is the setting value of S sufficient?Please set the maximum S value to 1000, and then perform the engraving test again.
2. In the laserGRBL software, enter $30=1000 in "type gcode here", and click the "Enter" key on the keyboard. Then do the engraving test again. (This is to set the default maximum power value of the laser to 1000)
3. Turn off the power of the machine and check whether the bottom lens of the laser module is dirty. Please use a cotton swab to wipe the laser lens to make sure the lens is clean, and then perform the engraving test again.
4. Properly reduce the speed. The speed of the plank is about 3000mm/min. Note that it is not mm/s. (lower speed possible)
5. Refer to the instruction manual to readjust the distance between the laser head and the object to be engraved. If the focus is not accurate, it will also result in failure to engrave. You can try different distances to see if there is a change.
6. If none of the above steps can solve the problem. Please project the laser on a farther wall in a place where there are no other people, take a picture and send it to us. (wear glasses and be careful)
https://drive.google.com/drive/folders/1YhnOJrokoGIlzK8Gt-KowzRl33gYFYNY?usp=share_link
1. In the "type gcode here" of the LaserGRBL software, input $32=1, and click the "Enter" key on the keyboard. (Enable Engraving Mode)
2. Select M4 mode in laserGRBL.Turn off "Constant Power Mode" in Lightburn.M4 is the engraving mode, which is more suitable for engraving.
3. If the problem is not solved, please update the firmware.(Please ask the manufacturer for the laser firmware, which is usually included in TF)
https://drive.google.com/drive/folders/1SCu5LlaNN7ZvDuZkpjAN2WNfcP-QCKbj?usp=share_link
https://drive.google.com/drive/folders/1SCu5LlaNN7ZvDuZkpjAN2WNfcP-QCKbj?usp=share_link
1. Move the X-axis and Y-axis, and observe whether the moving direction is correct?If the moving direction is not correctIn the "type gcode here" of LaserGRBL software, type $RST and hit "Enter" on the keyboard. Then perform the move test and engrave test. (This is to restore the default value)
2. If the problem is not solved, please update the firmware.(Please ask the manufacturer for the laser firmware, which is usually included in TF)
https://drive.google.com/drive/folders/1K9N3bqym9KiP4W0WiND4kPBqUZ9mtuYN?usp=share_link
https://drive.google.com/file/d/1tRjZUrIklKCP6QTU9h2j6Y14VJVUGhVH/view?usp=share_link
1. Change the usb port of the computer to use. Loose connector or insufficient voltage may cause the connection to be interrupted.
2. The USB cable is placed in a place to avoid touching. Pulling the USB cable may also cause the connection to be interrupted.
3. The above steps do not solve the problem, refresh the machine firmware.(Please ask the manufacturer for the laser firmware, which is usually included in TF)
https://drive.google.com/file/d/1tRjZUrIklKCP6QTU9h2j6Y14VJVUGhVH/view?usp=share_link
Check whether the screen cable is loose, and re-tighten it;
Remove the screen from the machine casing and put it on an insulating object to see if it is better. If it is better, add insulating tape between the screen and the machine casing when putting the screen back into the machine; if it still does not improve, it means that there is something wrong with the screen. Replace the screen.
Check whether the power supply voltage of the printer complies with the local rated voltage;
If the switch light is on, but the power light is not on, it may be that the wires on the power supply are connected incorrectly or the ship type switch is connected incorrectly, resulting in no power supply. You need to check whether the wires are connected correctly;
When both the switch light and the power light are on, but the main board light is not on, it may be that the main board cannot be used due to the short circuit of the broken material detection. You only need to re-edit the wiring sequence to solve it.
Check whether the card can be used normally on the computer. If the SD card can be used normally on the computer, save the file to the computer first, then format the card, and test it on the machine after formatting; if it cannot be recognized, It proves that there is a problem with the SD card and needs to be replaced;
The file code is wrong, the code needs to be renamed;
Check whether the motor is operating normally, if it stops rotating, try to restart the machine;
Try to troubleshoot the problem from the following points:
Motor drive current is too large, re-adjust the appropriate drive current;
The synchronous wheel of the motor is not fixed – retighten the synchronous wheel;
The hardware position of the machine, such as the optical shaft, the slider, and the lead screw, is stuck – manually adjust it until it is smooth after oiling;
The belt on the X Y axis is too loose – readjust the tension of the belt;
Try to troubleshoot the problem from the following points:
1. Check whether it is caused by the guide shaft and sliding operation, and lubricating oil can be used for lubrication;
2. Check whether the belt is off or misplaced, readjust and correct;
Preheat the nozzle to 200°, and clean up the waste on the heating block. Unscrew the two screws of the cooling block, and use tools to remove the heating block, throat, and nozzle in turn for cleaning. (Note: Be careful of high temperature during heat treatment and pay attention to safety)
For laser engraving, we usually suggest the two most available and well-known software: LaserGRBL and Lightburn.
LaserGRBL is the most common free software for laser engraving.
Lightburn is the most popular paid laser engraving software with more features and compatibility.
You might find more information on the website and choose which fits you best and download on their websites.
For Laser Engraving:
Lightburn: Windows 7.0 or later, 32 or 64 bit, MacOS 10.11 or later, or 64 bit Linux (Ubuntu 16+ or Fedora 28+, anything else may not work as intended).
LaserGRBL: LaserGRBL is compatible with Windows from XP to W10. 64 bit OS is strongly suggested in order to use all the features of LaserGRBL.
For 3D Printing
Cura:
Windows, macOS, Linux
Our 3D printers support Cure, Repetier-Host and any other slicers that could save printing file as Gcode formate.
1. Make sure the machine is turned on.
2. Make sure the USB cable is connected to the interface of the machine.
3. Check whether the computer can recognize the COM signal of the machine. (or into another port on your computer)
4. In the previous step, if there is no new com, you need to install a CH340 driver. You can search for the CH340 driver through a browser.
5. If the above steps still fail to connect, please restart your computer and reconnect. (because there may be a software conflict).
https://drive.google.com/file/d/1S_8mZ2WqUpZu2ja6emUGwr1Dqj67FgvB/view?usp=share_link
1. Check whether the motor cable is installed correctly (you can try to reinstall it) and check whether the cable is broken.
2. Check whether the driver on the motherboard is installed correctly.
3. Plug the wiring of the non-working motor into the normal motor, and observe whether the motor can still work normally. If it can, it means that the motor is damaged, if it cannot work, it is a problem with the motor wiring or drive;
4. Insert the driver corresponding to the non-working motor into the position where the normal motor is driven, and observe whether the motor can still work normally. If not, it means that the driver is damaged.
It may be caused by the following two situations.
1. The limit switch of the machine does not work.2. Friction of transmission parts.1. The limit switch does not work.1.1. Check whether the limit switch wiring is installed normally and whether there is any breakage1.2. Turn the good limit switch wiring on the main board and the non-working limit switch wiring position, check and judge whether the limit switch is damaged or the interface on the main board is damaged2. Friction of transmission parts.2.1. Turn off the power of the machine, move the X and Y axes left and right, check whether there is any sticking or difficulty in moving, test each driving part individually, adjust the screw or add lubricant according to each different part.2.2. Check whether the Z-axis screw rod is bent or deformed.
1. Modify the motor rotation direction to solve the problem1.1. Turn on the machine, click once on the screen: Settings - Machine settings - Motor - Motor Direction Settings, adjust the axis that needs to change the direction of the motor, save and exit2. Refresh the firmware to solve the problem2.1. Please refresh the correct firmware according to the driver model used by the machine
https://drive.google.com/file/d/1SgpI5hl6v9-VeFui1HYHCkId9NNP1hoZ/view?usp=share_link
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to open the demo video.
Please click here to download the file.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
English Version: DOWNLOAD
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
English Version: DOWNLOAD
Please click DOWNLOAD to initiate downloading.
English Version: DOWNLOAD
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Please click DOWNLOAD to initiate downloading.
Download
Please click and visit our DOWNLOAD PAGE to get firmware for your devices.
MAKE SURE TO CHECK THE TUTORIAL VIDEO BEFORE DOWNLOADING.
Please click DOWNLOAD to get TF files for your machines.
PLEASE NOTED: The maximum downloadable file size is 2GB, please only download needed file or download all files one by one.
BLU-3: DOWNLOAD
BLU-5: DOWNLOAD
SP-3: DOWNLOAD
SP-5: DOWNLOAD
TT-2.5/TT-5.5: DOWNLOAD
TT-5.5S: DOWNLOAD
CNC 3018 Pro: DOWNLOAD
TS3: DOWNLOAD
TS2-10W: DOWNLOAD
TS2-20W: DOWNLOAD
TTC450: DOWNLOAD
LightBurn
Please click and visit Lightburn official website to download the software.
If you want to buy LightBurn License key, please click here.
LaserGRBL
Please click and check LaserGRBL official website to download the software.
Cura
Please click and visit Cura official website to download the software.
Frequently Asked Questions
FOR SHIPPING &
RETURN POLICIES
We accept payment from PayPal, credit card and digital wallet.
1. PayPal
PayPal is a secure and trusted payment method for online shopping.
1) With PayPal, you can send payment quickly and securely online.
2) Through PayPal, you can pay with a credit card, debit card, or bank account balance even if you do not have a Paypal account.
3) Once your order is submitted, you will be redirected to PayPal to complete the transaction. You can trace the status of your payment using your PayPal account.
2. Credit/debit card
We accept payment from debit/credit cards (including American Express, Discover, JCB, Visa, Mastercard) with international transactions from most locations worldwide. Paying with a Credit or Debit Card is safe, easy and convenient.
How to pay with a credit card:
1) Select your shipping address or create a new one;
2) Enter your card details and click ”Submit”;
3) Your payment will be processed and a receipt will be sent to your e-mail address.
NOTE:
If several of your attempts have failed, please try again in 24 hours or use another payment method like PayPal.
3. E-wallet: Rabbit Line Pay & ShopeePay
We also accept payment from digital wallets including Rabbit Line Pay and ShopeePay.
We only accept the payment in USD dollars on our site. If your primary currency is not USD, you can still pay us USD in Paypal.
For orders shipped from our overseas warehouses, customers won't need to pay for the duty fees.
For orders shipped from China, customers need to bear the shipping costs and duty fees.
Regarding detailed duty fees, each country has its own tax policies and it's suggested to contact your local customs officers or search online to get more details.
We provide one-year warranty for our products.
Our Customers’ Feedback
FIND YOUR ANSWER
FROM REAL CUSTOMERS
Valentine Gibbs
I tried your coffee this past summer when my husband and I started going to the Wrightstown Farmers market. I haven't missed a week since for your delicious coffee. I used to buy the very popular coffee and found that yours was better tasting, better kept and made the perfect cup every time!! I even got my other family members hooked on it as well!! Thank you for the best cup of coffee!
Lisa Stone
You have not tried fresh coffee until you've tried this one. We saw this coffee roasted meticulously and shipped as soon as it came out of the roaster. Just try one bag and you will be hooked. We are true coffee "snobs" and this is the only coffee that suits our tastes. Try it in a french press for an unbelievable fresh coffee experience! Thank you so much! A Perfect cup every time!
Cliff Lindsey
My wife stumbled across The Coffee Scoop at a tasting demo held at Frey's Better Foods in Hellertown, PA. She bought a bag of coffee, and we've been hooked ever since. Not only are these the best coffees we've ever tasted, they're also organic and fair trade. We've since moved to Colorado, so now we order online. The shipments always arrive sooner than we expect. 110% happy customers.
Sacha Nichols
I purchased your coffee (coffee lover's blend) this weekend at Rice's and I am hooked. I opened my bag of beans and the aroma was incredible. I never realized that the coffee could smell that good. I couldn't wait to grind them up and make a pot. By far the best coffee I have ever brewed at home. I am going to be spreading the word to my other coffee lovers. Thank you.
Lisa St1one
You have not tried fresh coffee until you've tried this one. We saw this coffee roasted meticulously and shipped as soon as it came out of the roaster. Just try one bag and you will be hooked. We are true coffee "snobs" and this is the only coffee that suits our tastes. Try it in a french press for an unbelievable fresh coffee experience! Thank you so much! A Perfect cup every time!
Jeanne Town
Thank you for choosing and superbly skillfully roasting the most fabulous coffees! I was just perusing the high praise on the Testimonials page of your website. It was interesting how many glowing reviews there were of everything, but especially, in my case, of your Komodo Decaf. I couldn’t agree more. Not only is it the best decaf I have ever tasted, it’s one of the best coffees I have ever tasted!
